New pages

From Seawind1160Wiki
Jump to navigationJump to search
New pages
Hide registered users | Hide bots | Hide redirects

6 October 2026

26 September 2026

  • 15:5215:52, 26 September 2026 Propeller Zincs (hist | edit) [359 bytes] SwWikiAdminUser (talk | contribs) (Created page with "'''General'''<br> Manufacturer: BoatZincs.com<br> Description: Gori Triangle tip zinc<br> Model/Part Number: 14072100<br> <br> '''General'''<br> Manufacturer: BoatZincs.com<br> Description: Gori 2 piece zinc<br> Model/Part Number: 15527500<br> <br> '''General'''<br> Manufacturer: <br> Description: SD20 Split zinc<br> Model/Part Number: <br> <br>")

17 September 2026

  • 09:2209:22, 17 September 2026 Engine Removal (hist | edit) [349 bytes] SwWikiAdminUser (talk | contribs) (Created page with "'''Engine removal tips'''<br> #Use the main halyard to swing the new Yanmar 3YM30 onboard <br> #Two men on shoulder harness to carry downstairs<br> #Three men to lower down onto bed<br> #Use a come-along to hoist and lower into the correct position to align drive splines<br> '''Notes'''<br> *It is helpful to remove accessories to reduce weight<br>")
  • 09:2009:20, 17 September 2026 Coolant (hist | edit) [327 bytes] SwWikiAdminUser (talk | contribs) (Created page with "'''Coolant'''<br> Manufacturer: Yanmar<br> Description: Yanmar Diesel YG30R ELC Ultralife Coolant <br> Model/Part Number: 804056<br> Alternative: Zerex Nitrite Free Red Nitrite Free OAT Antifreeze or an equivalent ASTM D3306<br> '''Notes'''<br> *Coolant capacity: 4.3L<br> *Change interval: Every 5 years or 1000 hours<br> <br>")

16 September 2026

  • 09:0209:02, 16 September 2026 Bottom Paint (hist | edit) [903 bytes] SwWikiAdminUser (talk | contribs) (Created page with "'''General'''<br> Description: Application of bottom paint to hulls to prevent sea growth<br> '''Guides'''<br> # Sand with 80 grit sand paper # Wash with soap # Wipe with acetone (''Skip steps 1-3 if applying directly after last coat of barrier coat'') # Apply bottom paint coat #1 # Wait for layer to cure (''95 degrees = 4 hours, 77 degrees = 6 hours, 50 degrees = 20 hours'') # Apply bottom paint coat #2 # Wait for layer to cure (''95 degrees = 4 hours, 77 degrees = 6 h...")

15 September 2026

  • 14:3614:36, 15 September 2026 Barrier Coat (hist | edit) [2,927 bytes] SwWikiAdminUser (talk | contribs) (Created page with "'''General'''<br> Description: Application of barrier coat to hulls to prevent blisters<br> '''Notes'''<br> # Remove old bottom paint and barrier coat, exposing gel coat # Sand with 80 grit sand paper # Wash with soap # Wipe with Dewaxer & surface prep # Apply epoxy barrier coat (grey) # Wait for layer to cure, finger test (imprint left but no paint on your finger) # Apply epoxy barrier coat (white) # Wait for layer to cure, finger test (imprint left but no paint on your...")

14 September 2026

13 September 2026

12 September 2026

  • 10:0410:04, 12 September 2026 Outer Inner Diaphragm (hist | edit) [643 bytes] SwWikiAdminUser (talk | contribs) (Created page with "'''General'''<br> Description: There are two diaphragms attached to the saildrive that keep sea water from entering the boat with a sensor to detect water penetration of the outer diaphragm.<br> '''Notes'''<br> *Replacement Guidelines: Inspect every 2 year and replace every 5 years<br> *Common Practice: Monitor condition and test the water penetration sensor annually<br> *Recommendations: Pacwest in San Diego does not recommend changing the diaphragms unless there is vi...")
  • 09:5909:59, 12 September 2026 Saildrive Oil (hist | edit) [813 bytes] SwWikiAdminUser (talk | contribs) (Created page with "'''General'''<br> Manufacturer: Multiple<br> Type: 80W90W gear oil (API GL-4 or GL-5)<br> Capacity: 2.7L<br> '''Notes'''<br> *Change interval: Every 150 hours of operation or annually<br> *Blown seals: The SD20 is susceptible to blowing the seals if the oil is filled too high. Many have added a vent line to the top of the filler cap. Without the vent, only fill the saildrive oil to the bottom of the dipstick<br> <br> '''Procedure to change oil in the water:'''<br> #...")

11 September 2026

  • 09:3009:30, 11 September 2026 Lightning Protection (hist | edit) [403 bytes] SwWikiAdminUser (talk | contribs) (Created page with "'''General'''<br> Manufacturer: Moonraker<br> Description: Lightning protection grounding plates <br> Quantity: 2<br> Wiring: Plates are in-line with the mast and are connected to the mast base<br> Location: Port aft, below the waterline<br> '''Notes'''<br> DO NOT cover with antifoul<br> '''Pictures'''<br> thumb|Moonraker Earth Plates for lightening protection")
  • 07:3807:38, 11 September 2026 Upgrading Lithium (hist | edit) [2,102 bytes] SwWikiAdminUser (talk | contribs) (Created page with "'''General'''<br> '''''Caution:''''' Lithium battery bank upgrades are not drop in replacements; you MUST do your own research, get expert advice, and have a profession installation<br> '''''Note:''''' This page is strictly a starting point to point out the biggest considerations and should not be taken as a guide to follow<br> <br> '''Keys to upgrading to a lithium battery bank'''<br> # Only consider LiFePO4 chemistry; the failure mode of LiFePO4 will cause smoke but n...")

29 August 2026

6 August 2026

  • 12:1712:17, 6 August 2026 Engine Control Panel (hist | edit) [460 bytes] SwWikiAdminUser (talk | contribs) (Created page with "'''Type B Yanmar Panel'''<br> Description: Panel with key, tachometer, and engine sensor lights<br><br> '''Replacement Tachometer'''<br> Manufacturer: VDO<br> Part Number: 333-963B<br> Description: VDO Tachometer Gauge 4000 RPM with hour meter<br><br> '''Replacement Tachometer Lens'''<br> Manufacturer: VDO<br> Part Number: N05-801-834<br> Description: Lens Oceanline 85mm<br><br>")

29 July 2026

  • 12:5112:51, 29 July 2026 Sheared tapper pin repair (hist | edit) [260 bytes] SwWikiAdminUser (talk | contribs) (Created page with "''Sheared tapper pin repair:'' [https://www.strikhedonia.com/anchoring-with-no-starboard-engine-in-a-crowded-anchorage/ External Link]<br><br>")
  • 12:4612:46, 29 July 2026 Propeller Shaft Grooves (hist | edit) [1,001 bytes] SwWikiAdminUser (talk | contribs) (Created page with "'''Propeller Shaft Grooves'''<br> It is an issue that Gori propellers installed on a SD20 saildrive will form grooves over time which will result in sea water penetration. Periodic repositioning of the seals using shims allow longer life from the propeller shafts.<br><br> Methods to deal with groves on the propeller shaft: # Add/re-position spacers between the seals # Machine propeller shaft and add a 316SS sleeve to return to original size (35mm) # Replace propeller sh...")
  • 08:3708:37, 29 July 2026 Saildrive Part Numbers (hist | edit) [726 bytes] SwWikiAdminUser (talk | contribs) (Created page with "'''Part Numbers'''<br> Saildrive seal replacement kit<br> 196313-02591 Saildrive seal, oil prop shaft (Qty 2 per saildrive)<br> 24321-000950 Saildrive rear cover O-ring (Qty 2 per saildrive)<br> 24341-000125 O-Ring, drain plug (Qty 1 per saildrive)<br> 196315-02880 Circlip, Needle 52 (optional to reposition seals) previously 196313-02600<br><br> Others<br> 196420-02551 Rubber protector, saildrive leg<br> 196420-02602 Saildrive, rear cover<br> 196311-04060 Needle Bea...")
Retrieved from "https://strikhedonia.com/Seawind1160Wiki/index.php?title=Special:NewPages"