Saildrives: Difference between revisions
No edit summary |
No edit summary |
||
| Line 6: | Line 6: | ||
O-Ring parts diagram: [[File:SD20 O-rings Parts Diagram .pdf|thumb|Link]] <br> | O-Ring parts diagram: [[File:SD20 O-rings Parts Diagram .pdf|thumb|Link]] <br> | ||
Service Bulletin - Taper pin: [[File:SD20 Taper Pin Bulletin.pdf|thumb|Link]] <br><br> | Service Bulletin - Taper pin: [[File:SD20 Taper Pin Bulletin.pdf|thumb|Link]] <br><br> | ||
Needed for saildrive seal replacement<br> | |||
196313-02591 Saildrive seal, oil prop shaft (qty 2 per saildrive)<br> | |||
24321-000950 Saildrive rear cover O-ring (qty 2 per saildrive)<br> | |||
24341-000125 O-Ring, drain plug (qty 1 per saildrive)<br><br> | |||
Others<br> | |||
196420-02551 Rubber protector, saildrive leg<br> | |||
196420-02602 Saildrive, rear cover<br> | |||
196311-04060 Needle Bearing<br> | |||
196440-02701 Bolt, Bracket (Split zinc bracket, flat head M6X18)<br> | |||
26453-100252 Bolt, M10X25 (Saildrive rear cover bolt)<br><br> | |||
'''Notes:'''<br> | '''Notes:'''<br> | ||
''Blown seals:'' The SD20 is susceptible to blowing the seals if the oil is filled too high. Many have added a vent line to the top of the filler cap. Without the vent, only fill the saildrive oil to the bottom of the dipstick<br> | ''Blown seals:'' The SD20 is susceptible to blowing the seals if the oil is filled too high. Many have added a vent line to the top of the filler cap. Without the vent, only fill the saildrive oil to the bottom of the dipstick<br> | ||
Revision as of 16:24, 28 May 2026
Manufacturer: Yanmar
Description: Saildrive Unit
Model: SD20
Manual: File:SD20 Operations Manual 2009.pdf
Parts catalog: File:SD20 Part Catalog.pdf
O-Ring parts diagram: File:SD20 O-rings Parts Diagram .pdf
Service Bulletin - Taper pin: File:SD20 Taper Pin Bulletin.pdf
Needed for saildrive seal replacement
196313-02591 Saildrive seal, oil prop shaft (qty 2 per saildrive)
24321-000950 Saildrive rear cover O-ring (qty 2 per saildrive)
24341-000125 O-Ring, drain plug (qty 1 per saildrive)
Others
196420-02551 Rubber protector, saildrive leg
196420-02602 Saildrive, rear cover
196311-04060 Needle Bearing
196440-02701 Bolt, Bracket (Split zinc bracket, flat head M6X18)
26453-100252 Bolt, M10X25 (Saildrive rear cover bolt)
Notes:
Blown seals: The SD20 is susceptible to blowing the seals if the oil is filled too high. Many have added a vent line to the top of the filler cap. Without the vent, only fill the saildrive oil to the bottom of the dipstick
Sheared tapper pin repair: External Link
Oil specifications: 80W90W gear oil (API GL-4 or GL-5)
Oil capacity: 700ml
Oil change interval: Every 250 hours of operation or annually (whichever comes first)
Procedure to change oil in the water:
- Using a pump with a small tube remove as much oil as possible
- Refill oil to full capacity (bottom of dipstick)
- Run engine 5 minutes
- Using a pump with a small tube remove as much oil as possible
- Refill oil to full capacity (bottom of dipstick)
- (This will replace over 75% of the oil)
Outer diaphragm and secondary inner diaphragm
Replacement Guidelines: Inspect every 2 year and replace every 5 years
Common Practice: Monitor condition and test the water penetration sensor
Recommendations: Pacwest in San Diego does not recommend changing the diaphragms unless there is visible damage or water has penetrated the outer diaphragm. These diaphragm almost never fail. I have read this from other sources who make the same recommendation.
Propeller Shaft Grooves
It is an issue that they Gori propellers installed on a SD20 saildrive will form grooves over time which will result in sea water penetration. Periodic repositioning of the seals using shims allow longer life from the propeller shafts.
