Barrier Coat - Revision history

SwWikiAdminUser at 14:20, 16 September 2026

2026-09-16T14:20:45Z

← Older revision		Revision as of 08:20, 16 September 2026
Line 6:		Line 6:
	# Wash with soap		# Wash with soap
	# Wipe with Dewaxer & surface prep		# Wipe with Dewaxer & surface prep
	# Apply epoxy barrier coat (grey)		# Apply epoxy barrier coat (grey) #1
	# Wait for layer to cure, finger test (imprint left but no paint on your finger)		# Wait for layer to cure, finger test (imprint left but no paint on your finger)
	# Apply epoxy barrier coat (white)		# Apply epoxy barrier coat (white) #2
	# Wait for layer to cure, finger test (imprint left but no paint on your finger)		# Wait for layer to cure, finger test (imprint left but no paint on your finger)
	# Apply epoxy barrier coat (white)		# Apply epoxy barrier coat (grey) #3
	# ~~Repeat until five layers have been applied~~		# Wait for layer to cure, finger test (imprint left but no paint on your finger)
			# Apply epoxy barrier coat (white) #4
			# Wait for layer to cure, finger test (imprint left but no paint on your finger)
			# Apply epoxy barrier coat (grey) #5
	'''Notes'''<br>		'''Notes'''<br>
	:* If application requires more than one day, wipe with Dewaxer & surface prep at the start of each day		:* If application requires more than one day, wipe with Dewaxer & surface prep at the start of each day

SwWikiAdminUser at 14:17, 16 September 2026

2026-09-16T14:17:30Z

← Older revision		Revision as of 08:17, 16 September 2026
Line 40:		Line 40:
	*Quantity: 2		*Quantity: 2
	Deluxe Red Mohair Paint Roller Cover - 9"		Deluxe Red Mohair Paint Roller Cover - 9"
	~~Brand~~: RedTree		*Manufacturer: RedTree
	*Model/Part Number: 29113		*Model/Part Number: 29113
	*Quantity: 10		*Quantity: 10

SwWikiAdminUser at 14:16, 16 September 2026

2026-09-16T14:16:56Z

SwWikiAdminUser at 14:14, 16 September 2026

2026-09-16T14:14:29Z

← Older revision		Revision as of 08:14, 16 September 2026
Line 12:		Line 12:
	# Apply epoxy barrier coat (white)		# Apply epoxy barrier coat (white)
	# Repeat until five layers have been applied		# Repeat until five layers have been applied
			'''Notes'''<br>
	:* If application requires more than one day, wipe with Dewaxer & surface prep at the start of each day		:* If application requires more than one day, wipe with Dewaxer & surface prep at the start of each day
	:* If using TotalBoat, there is a 60 day window between applying coats		:* If using TotalBoat, there is a 60 day window between applying coats
Line 23:		Line 24:
	:*4-5 coats when using a 3/16" Mohair roller cover (leaves the smoothest finish)		:*4-5 coats when using a 3/16" Mohair roller cover (leaves the smoothest finish)
	:* First layer of antifoul needs to go on after finger test is passed, if it gets hard it must be sanded with 80 grit, washed with soap, wiped with dewaxer & prep (make sure to do last barrier coat the day of the anti-foul application!)		:* First layer of antifoul needs to go on after finger test is passed, if it gets hard it must be sanded with 80 grit, washed with soap, wiped with dewaxer & prep (make sure to do last barrier coat the day of the anti-foul application!)
	~~'''Notes'''<br>~~
	Dewaxer & Surface Prep Solvent (gallon)		Dewaxer & Surface Prep Solvent (gallon)
	*Manufacturer: TotalBoat		*Manufacturer: TotalBoat

SwWikiAdminUser at 14:13, 16 September 2026

2026-09-16T14:13:32Z

@@ Line 1: / Line 1: @@
 '''General'''<br>
 Description: Application of barrier coat to hulls to prevent blisters<br>
-'''Notes'''<br>
+'''Guides'''<br>
 # Remove old bottom paint and barrier coat, exposing gel coat
 # Sand with 80 grit sand paper
@@ Line 21: / Line 21: @@
 :*After the induction period, this product can be thinned as necessary, up to 10% by volume with Epoxy Primer Thinner for all application methods - ONLY add thinner if you find the barrier coat is getting thick in the tray
 :*When rolling, use a solvent-safe 3/16" foam or nap roller cover.
-:*4-5 coats when using a 3/16" roller cover (leaves the smoothest finish)
+:*4-5 coats when using a 3/16" Mohair roller cover (leaves the smoothest finish)
 :* First layer of antifoul needs to go on after finger test is passed, if it gets hard it must be sanded with 80 grit, washed with soap, wiped with dewaxer & prep (make sure to do last barrier coat the day of the anti-foul application!)

SwWikiAdminUser at 20:53, 15 September 2026

2026-09-15T20:53:34Z

← Older revision		Revision as of 14:53, 15 September 2026
Line 22:		Line 22:
	:*When rolling, use a solvent-safe 3/16" foam or nap roller cover.		:*When rolling, use a solvent-safe 3/16" foam or nap roller cover.
	:*4-5 coats when using a 3/16" roller cover (leaves the smoothest finish)		:*4-5 coats when using a 3/16" roller cover (leaves the smoothest finish)
	:* First layer of antifoul needs to go on after finger test ~~past~~, if it gets hard it must be sanded with 80 grit, washed with soap, wiped with dewaxer & prep (make sure to do last barrier coat the day of the ~~anit~~-foul application!		:* First layer of antifoul needs to go on after finger test is passed, if it gets hard it must be sanded with 80 grit, washed with soap, wiped with dewaxer & prep (make sure to do last barrier coat the day of the anti-foul application!)

SwWikiAdminUser at 20:52, 15 September 2026

2026-09-15T20:52:29Z

← Older revision		Revision as of 14:52, 15 September 2026
Line 19:		Line 19:
	:*Stir the two components together thoroughly for 3-5 minutes, until it forms a uniform, consistent liquid.		:*Stir the two components together thoroughly for 3-5 minutes, until it forms a uniform, consistent liquid.
	:*Once mixed, allow this product to sit for 15 minutes. DO NOT ADD ANY THINNER AT THIS TIME. This is the induction period where the two components will begin to react, allowing for the proper cross-linking prior to being applied.		:*Once mixed, allow this product to sit for 15 minutes. DO NOT ADD ANY THINNER AT THIS TIME. This is the induction period where the two components will begin to react, allowing for the proper cross-linking prior to being applied.
	:*After the induction period, this product can be thinned as necessary, up to 10% by volume with Epoxy Primer Thinner for all application methods.		:*After the induction period, this product can be thinned as necessary, up to 10% by volume with Epoxy Primer Thinner for all application methods - ONLY add thinner if you find the barrier coat is getting thick in the tray
	:*When rolling, use a solvent-safe 3/16" foam or nap roller cover.		:*When rolling, use a solvent-safe 3/16" foam or nap roller cover.
	:*4-5 coats when using a 3/16" roller cover (leaves the smoothest finish)		:*4-5 coats when using a 3/16" roller cover (leaves the smoothest finish)
	:* First layer of antifoul needs to go on after finger test past, if it gets hard it must be sanded with 80 grit, washed with soap, wiped with dewaxer & prep (make sure to do last barrier coat the day of the anit-foul application!		:* First layer of antifoul needs to go on after finger test past, if it gets hard it must be sanded with 80 grit, washed with soap, wiped with dewaxer & prep (make sure to do last barrier coat the day of the anit-foul application!

SwWikiAdminUser at 20:51, 15 September 2026

2026-09-15T20:51:29Z

← Older revision		Revision as of 14:51, 15 September 2026
Line 12:		Line 12:
	# Apply epoxy barrier coat (white)		# Apply epoxy barrier coat (white)
	# Repeat until five layers have been applied		# Repeat until five layers have been applied
	:* If application requires more than one day, wipe with Dewaxer & surface prep the start of each day		:* If application requires more than one day, wipe with Dewaxer & surface prep at the start of each day
	:* If using TotalBoat, there is a 60 day window between applying coats		:* If using TotalBoat, there is a 60 day window between applying coats
	:*All bare fiberglass substrates need to be fully cured for at least 5-7 days prior to any surface preparation		:*All bare fiberglass substrates need to be fully cured for at least 5-7 days prior to any surface preparation (3 days at 80-90 degrees)
	:*Dewax the surface using the two-rag method: Start with a clean, lint-free cotton rag wetted with ~~TotalBoat~~ Dewaxer & Surface Prep. Follow the wetted rag with a dry, clean cotton rag to help remove any contaminants remaining on the surface. Perform this two-rag method 2-3 times to ensure all wax and potential contaminants have been removed		:*Dewax the surface using the two-rag method: Start with a clean, lint-free cotton rag wetted with Dewaxer & Surface Prep. Follow the wetted rag with a dry, clean cotton rag to help remove any contaminants remaining on the surface. Perform this two-rag method 2-3 times to ensure all wax and potential contaminants have been removed
	:*The entire surface to be barrier coated should have a uniform dull, frosty finish		:*The entire surface to be barrier coated should have a uniform dull, frosty finish
	:*Stir the two components together thoroughly for 3-5 minutes, until it forms a uniform, consistent liquid.		:*Stir the two components together thoroughly for 3-5 minutes, until it forms a uniform, consistent liquid.
Line 22:		Line 22:
	:*When rolling, use a solvent-safe 3/16" foam or nap roller cover.		:*When rolling, use a solvent-safe 3/16" foam or nap roller cover.
	:*4-5 coats when using a 3/16" roller cover (leaves the smoothest finish)		:*4-5 coats when using a 3/16" roller cover (leaves the smoothest finish)
			:* First layer of antifoul needs to go on after finger test past, if it gets hard it must be sanded with 80 grit, washed with soap, wiped with dewaxer & prep (make sure to do last barrier coat the day of the anit-foul application!

SwWikiAdminUser: Created page with "'''General'''
Description: Application of barrier coat to hulls to prevent blisters
'''Notes'''
# Remove old bottom paint and barrier coat, exposing gel coat # Sand with 80 grit sand paper # Wash with soap # Wipe with Dewaxer & surface prep # Apply epoxy barrier coat (grey) # Wait for layer to cure, finger test (imprint left but no paint on your finger) # Apply epoxy barrier coat (white) # Wait for layer to cure, finger test (imprint left but no paint on your..."

2026-09-15T20:36:54Z

Created page with "'''General''' Description: Application of barrier coat to hulls to prevent blisters '''Notes''' # Remove old bottom paint and barrier coat, exposing gel coat # Sand with 80 grit sand paper # Wash with soap # Wipe with Dewaxer & surface prep # Apply epoxy barrier coat (grey) # Wait for layer to cure, finger test (imprint left but no paint on your finger) # Apply epoxy barrier coat (white) # Wait for layer to cure, finger test (imprint left but no paint on your..."

New page

'''General''' 
Description: Application of barrier coat to hulls to prevent blisters 
'''Notes''' 
# Remove old bottom paint and barrier coat, exposing gel coat
# Sand with 80 grit sand paper
# Wash with soap
# Wipe with Dewaxer & surface prep
# Apply epoxy barrier coat (grey)
# Wait for layer to cure, finger test (imprint left but no paint on your finger)
# Apply epoxy barrier coat (white)
# Wait for layer to cure, finger test (imprint left but no paint on your finger)
# Apply epoxy barrier coat (white)
# Repeat until five layers have been applied
:* If application requires more than one day, wipe with Dewaxer & surface prep the start of each day
:* If using TotalBoat, there is a 60 day window between applying coats
:*All bare fiberglass substrates need to be fully cured for at least 5-7 days prior to any surface preparation
:*Dewax the surface using the two-rag method: Start with a clean, lint-free cotton rag wetted with TotalBoat Dewaxer & Surface Prep. Follow the wetted rag with a dry, clean cotton rag to help remove any contaminants remaining on the surface. Perform this two-rag method 2-3 times to ensure all wax and potential contaminants have been removed
:*The entire surface to be barrier coated should have a uniform dull, frosty finish
:*Stir the two components together thoroughly for 3-5 minutes, until it forms a uniform, consistent liquid.
:*Once mixed, allow this product to sit for 15 minutes. DO NOT ADD ANY THINNER AT THIS TIME. This is the induction period where the two components will begin to react, allowing for the proper cross-linking prior to being applied.
:*After the induction period, this product can be thinned as necessary, up to 10% by volume with Epoxy Primer Thinner for all application methods.
:*When rolling, use a solvent-safe 3/16" foam or nap roller cover.
:*4-5 coats when using a 3/16" roller cover (leaves the smoothest finish)

← Older revision		Revision as of 08:16, 16 September 2026
Line 14:		Line 14:
	'''Notes'''<br>		'''Notes'''<br>
	:* If application requires more than one day, wipe with Dewaxer & surface prep at the start of each day		:* If application requires more than one day, wipe with Dewaxer & surface prep at the start of each day
	:* ~~If using TotalBoat, there~~ is a 60 day window between applying coats		:* There is a maximum 60 day window between applying coats
	:*All bare fiberglass substrates need to be fully cured for at least 5-7 days prior to any surface preparation (3 days at 80-90 degrees)		:*All bare fiberglass substrates need to be fully cured for at least 5-7 days prior to any surface preparation (3 days at 80-90 degrees)
	:*Dewax the surface using the two-rag method: Start with a clean, lint-free cotton rag wetted with Dewaxer & Surface Prep. Follow the wetted rag with a dry, clean cotton rag to help remove any contaminants remaining on the surface. Perform this two-rag method 2-3 times to ensure all wax and potential contaminants have been removed		:*Dewax/Prep the surface using the two-rag method: Start with a clean, lint-free cotton rag wetted with Dewaxer & Surface Prep. Follow the wetted rag with a dry, clean cotton rag to help remove any contaminants remaining on the surface. Perform this two-rag method 2-3 times to ensure all wax and potential contaminants have been removed
	:*The entire surface to be barrier coated should have a uniform dull, frosty finish		:*The entire surface to be barrier coated should have a uniform dull, frosty finish
	:*Stir the two components together thoroughly for 3-5 minutes, until it forms a uniform, consistent liquid.		:*Stir the two components together thoroughly for 3-5 minutes, until it forms a uniform, consistent liquid.
	:*Once mixed, allow this product to sit for 15 minutes. DO NOT ADD ANY THINNER AT THIS TIME. This is the induction period where the two components will begin to react, allowing for the proper cross-linking prior to being applied.		:*Once mixed, ''allow this product to sit for 15 minutes''. DO NOT ADD ANY THINNER AT THIS TIME. This is the induction period where the two components will begin to react, allowing for the proper cross-linking prior to being applied.
	:*After the induction period, this product can be thinned as necessary, up to 10% by volume with Epoxy Primer Thinner for all application methods - ONLY add thinner if you find the barrier coat is getting thick in the tray		:*After the induction period, this product can be thinned as necessary, up to 10% by volume with Epoxy Primer Thinner for all application methods - ''ONLY add thinner if you find the barrier coat is getting thick in the tray
	~~:*When rolling, use a solvent-safe 3/16" foam or nap roller cover.~~
	:*4-5 coats when using a 3/16" Mohair roller cover (leaves the smoothest finish)		:*4-5 coats when using a 3/16" Mohair roller cover (leaves the smoothest finish)
	:* First layer of antifoul needs to go on after finger test is passed, if it gets hard it must be sanded with 80 grit, washed with soap, wiped with dewaxer & prep ~~(make sure to~~ do last barrier coat the day of the anti-foul application!)		:* First layer of antifoul needs to go on after finger test is passed, if it gets hard it must be sanded with 80 grit, washed with soap, wiped with dewaxer & prep - ''do last barrier coat the day of the anti-foul application!''
	Dewaxer & Surface Prep Solvent (gallon)		Dewaxer & Surface Prep Solvent (gallon)
	*Manufacturer: TotalBoat		*Manufacturer: TotalBoat