December 30, 2020
For real, I think the spar tunnel is done until the wings go on… Started off adding connectors and drilling brackets made by fellow builder Leo for a set screw need to keep the Tosten stick grips from spinning. Then moved back into wiring mode to work on the connectors that stick grips plug into. That took awhile… Also soldered…
December 20, 2020
I started the day finishing up the wiring – well there is still wiring to do once the wings are on and the control sticks are in. Oh and once the carbon fiber panel comes back from the painter (respraying due to poor adhesion) I can connect the wires to the switches. But other than that is is done. Whew…
December 19, 2020
More work on the wiring. Began with the fun time installing not one but two Adel clamps on the same screw on different side of the support. That was fun. Then back to the VPX. I’m down to 7 or 8 switches, and about 7 or 8 power circuits. Then it will be time for testing and troubleshooting. I sure…
December 18, 2020
Overnight I realized I missed the wires for the doors unlatched switches, oops. Along with pulling a new Com1 antenna wire I finished off running the wires. I still have a bunch of terminations to do on the VPX but then I should be done. Fingers crossed the avionics works when I flip the switch. A fellow RV-10 builder has…
December 17, 2020
Yep, wiring is a slow process. With no way to take exciting pictures, you will have to settle for a couple boring ones. Today was running the last of the wiring (I think) for the control sticks and for the light controller. Both will be located under the front seats. I did work on two of the VPX connectors but…
December 16, 2020
It might not look like it but today was a good day with good progress. Two of the three power connectors on the VPX are wired, one of the alterantor voltage regulators is wired, the fuel pump is wired, and the lower wires are organized. Yep, wiring doesn’t look like a lot but it sure takes time.
December 15, 2020
I came into the hanger this morning to find brake fluid under the fuselage. No bueno. Seems the tunnel brake fittings were not tightened, ugh. Shame on me for not double checking. My penance, 90 minutes of cleaning. Fluid leaked between ribs and skin, spar and skin, into every crack and crevice. Fuck me. Oh the day didn’t stop there.…
December 13, 2020
Yep, I said it. I finished up the back half of the plane wiring in the morning and then organized/zip tied/secured the cables. Then the fun began on the panel wiring. I already built the harness but with moving it from Minnesota, to setting it up and taking it down a couple times in the hanger (to finish the remaining…
December 11, 2020
More jumping around today, the seat back brackets are cut and deburred. Next week when my daughter visits we should be able to get the rear seats finished up giving her something she can point to and say “I did that!” Most of the day was on wiring. I got to ELT mounted and tied up all the tail cone…
December 10, 2020
Took some time but I got all the nut plates for the instruments installed and the instruments mounted. Also got the defrost fans installed, wired up, and tested. Then it was on to the baggage and rear seat pans. All the parts are now dimpled and deburred. Still nervous about a missed wire so I’ll hold off on riveting them…
December 9, 2020
The Aerosport panel sections near the firewall tilt up and results in the inability to drill a hold in them to secure to the tunnel cover. So today started with making a couple brackets to secure that two parts. That done I dropped off the carbon fiber pieces to Gene Kear (719-338-0173) a local legend who is going to give…
December 8, 2020
I decided I needed to make some adjustments to the mounting brackets for the transponder which morphed into giving all of the support brackets a good paint job. That along with a little more work on the baggage door took up a good chunk of the morning. After lunch I ran two cables I had forgotten for the overhead lights…